#Amp stock stereo how to#
#Amp stock stereo install#
#Amp stock stereo manual#
#Amp stock stereo Patch#

Note that the kit is likely to have a cable for a 2-channel amp which you might need.īefore you start the process, make sure you have: When you are dealing with a 4-channel amp and have chosen RCA cables to wire it, you will need to buy a second pair and an amp wiring kit, if you don’t have them already.

Step 6: Connect the battery, switch on the stereo and test the amplifier and speakers.

Plug in the RCA cables from the LOC to the amplifier.

Step 5: Cover the connection with electrical tape and make sure the wires are secure together.

And do the same with the front right wires too. Now connect the LOC’s front left to the stereo wire’s side.

Step 4: Remove about an inch of the insulation of the LOC wire and the stereo wire.

This will make it easy for you to connect the wires to the corresponding terminals. Learn about the connections and the wiring on your LOC.

Step 3: Take a look at the high input amp wiring diagram along with the diagram for the stereo output wires.

#Amp stock stereo manual#

It is best to check out the user manual to be able to do this safely because you might have to remove a few screws to take off the panels. For this, you will need to take out the factory head unit. Step 2: You need to locate the wire that connects to the LOC.Step 1: Disconnect the negative terminal of the battery to make sure there are no electrical problems like short circuits or blown fuses.Using a line output converter makes it easy to control the different signals coming in from various channels to the radio. This is a popular choice because the connection uses RCA cables which provide an input signal directly to the amp. If you want the amplifier to accept the high-level input directly, you can use a high-to-low converter and that is what an LOC is for. This makes sure that the subwoofer is not overworked when it is balancing the output trim level of the amplifier.

The line output converter also has an RCA adapter for amp which connects to the stock radio and takes the speaker-level input signal coming in at high voltage and converts it into a preamp-level signal that brings it to an acceptable power range for the amplifier at hand.Ī line output converter also has a feature that lets you adjust the gain so that the output is tweaked. You need to ground the transformer of the device with LOC cables meant for this purpose.

#Amp stock stereo Patch#

It connects to the amplifier using an RCA patch cable. Use a Line Output ConverterĪ line output converter or an LOC has a high-voltage resistor and a transformer. Here are the popular choices to wire high-level input on an amplifier.

This is not a bad way to go because, in the end, it does give you flexibility in terms of installation irrespective of the type of system you are dealing with. Instead, a lot of people just use RCA cables. This is also because high-level input systems need you to make changes to the wiring of the car. They can even degrade the signal if the connections are not made properly. This is true even when you use aftermarket stereo systems.īut not many people pay attention to this because the output does not seem as different. Typically, factory audio systems that have high-level inputs do not sound nearly as good as low-level input connections. Let’s take a look at the connections and how you need to wire them for the output you desire.

#Amp stock stereo how to#

Now, we will tell you how to hook up an amp without RCA jacks but if you have a pair of them, it’s not a problem. So, manufacturers came up with a solution that requires you to use high-level input so that their products can be connected and played in the newer cars.

#Amp stock stereo install#

Now, a lot of factor radios don’t come with RCA jacks which makes it very difficult to install an amp in an audio system. This is how you get an input signal to the amp. If you didn’t know it already, a high-level input is just another way of saying you will use the speaker wire lead behind the radio instead of RCA cables and connect them to the amplifier. If you are not sure about how to wire high-level input on an amp, here’s a look. Here’s how you can do that by using low and high-level inputs either exclusively or in combination.

Now, there are a few ways to make this happen and one of them is to connect more than one amplifier to get the desired outputs. One of the functions of an amplifier is to accept a signal from one source like your radio and improve the sound quality and speaker level input to give you a better listening experience. Audio amplifiers for cars come in many different configurations.